Just curious on this. Over time, a horn will pick up a few belt scratches, small insignificant dents, maybe minor bell scratches from setting it "bell down" on the floor during practice or rehearsal (which I realize is verboten), the finish fading in some spots, etc. And if you buy a used horn, some of those issues come with it. And I'm referring to issues that don't affect playability. Do any of you ever completely refurbish your horns to "like new", or is that even possible, and is it an expense that's not ever necessary?
Sponsor Banner
Collapse
Refurbishing your horn
Collapse
X
-
I put my 1923 Conn 86I in for a complete rehab job, including replating the valves, a couple years ago. It was an expensive proposition ($1800), and I probably won't recover that cost if I ever sell it, but it was worth the expense to me; the horn looks like it just came from the factory (which was about a mile from our house). I've owned that horn since 1960; we bought it for $200 from the original owner.
DDavid Bjornstad
1923 Conn New Wonder 86I, Bach 6 1/2 AL
2018 Wessex EP100 Dolce, Denis Wick 4ABL
2013 Jinbao JBEP-1111L, Denis Wick 4AM
2015 Jinbao JBBR-1240, Denis Wick clone mouthpiece of unknown designation
Cullman (AL) Community Band (Euph Section Leader)
Brass Band of Huntsville (2nd Bari)
-
-
I had a rather unfortunate accident a while ago with my last horn, rendering it unplayable. Since I needed my horn for my studies, refurbishing it was my only option since it was far cheaper than buying a new one. I shipped my horn to McQueens for the job, a well known reputable brass shop based in Manchester, UK. You can find the thread I worte about all that right here: http://www.dwerden.com/forum/showthr...etely-restored!
The cost of a refurb, while steep, was justified in my case since my instrument was not playable anymore. Be aware that a refurb involves completely dissasembling an instrument, undenting all the parts, filling up possible cracks in the brass, sanding off the finish, assembling everything back together and refinishing it. As they sand off the finish, a tiny layer of brass will come off too, so with all the parts realigned, undented and the loss of some material there will most likely be a change in the playing characteristics of the instrument. In my particular case the fourth valve played even more stuffy than before, but your experience may vary. In the end I did not regret my decision to getting my euph refurbished as it still played better than it was after the accident. I would not recommend to refurbish a horn over some cosmetical damage as long as it still plays well.
This link directs to a great video where an old King baritone gets an complete overhaul with commentary by the brass technician: https://www.youtube.com/watch?v=mSRc...annel=jimflys2Last edited by Vito; 09-22-2020, 01:02 PM.Music educator - Brass Instruments Enthusiast - Euphonium Player
2019 Besson Sovereign 967T-2 - Alliance DC3
Comment
-
-
My New Standard was completely restored by Dan Oberloh in Seatle a few years ago. Not cheap ($3,500), but it was ultimately worth it.
I was really picky, Dan really put up with me, and it looks gorgeous. It was upgraded to emulate a Prestige.
Dennis
Comment
-
-
I think, for a full Refurbish treatment, there really is a certain level it has to have reached, as well as some connection you may have with the horn.
If the cost of getting something you just bought restored to "like new" is more than simply finding another better example and selling yours, it's not really worth it. Many of my horns are used, and they have a little wear, a few minor dents, etc, but nothing bad enough that would justify a total teardown. There is quite a bit that can be fixed without having to do a full restore.
Here are two examples from the Oberloh website, probably from 10+ years ago:
http://www.oberloh.com/silvermirafoneeconojob.htm
http://www.oberloh.com/gallery/alxcctuba.htmSterling / Perantucci 1065HGS Euphonium, 1952 B&H Imperial Eb Tuba, and a bunch of trombones.
Comment
-
-
I had my 1980 round stamp redone around mid 1990's. It was a lacquer horn with lots of wear due to the fragile nature of the old nitrocellulose lacquer that Besson used. No serious dents, but lots of nicks and scratches. While I gave it to Osmun Music to do, they actually shipped it to one shop in Minnesota for disassembly, stripping, de-denting, brass polish. It the valve section went to Anderson Plating in Elkhart, IN for valve replating and machining. Then the horn was re-assembled in Minnesota and went back to Anderson for final silver plate (to replace the lacquer). I recall that I paid $1,500 (20 years ago). I think I originally purchased the horn for around $800. I sold it in 2007 to a student of Dave Werden's for $3,000.
Now, using this experience is problematic since it was over 20 years ago. Further, Anderson no longer does the valve work (and there are few places in the US that do.)Adams E3 0.60 Sterling bell - Prototype top sprung valves
Concord Band
Winchendon Winds
Townsend Military Band
Comment
-
-
Originally posted by daruby View PostFurther, Anderson no longer does the valve work (and there are few places in the US that do.)
DDavid Bjornstad
1923 Conn New Wonder 86I, Bach 6 1/2 AL
2018 Wessex EP100 Dolce, Denis Wick 4ABL
2013 Jinbao JBEP-1111L, Denis Wick 4AM
2015 Jinbao JBBR-1240, Denis Wick clone mouthpiece of unknown designation
Cullman (AL) Community Band (Euph Section Leader)
Brass Band of Huntsville (2nd Bari)
Comment
-
-
Originally posted by DaveBj View PostWhen did they quit? They did my Conn's valves, and that was just a couple years ago.D
Replating and machining the piston after replating is not the hard part. The hard part is boring and honing the cylinder (with the large holes all around it) and ending up with a perfectly round and straight sided cylinder, and THEN getting a replated piston to fit with just the right tolerances. I had a long conversation with Paul Riggett on this topic when his techs were working with York in Markneukirchen from about 2007-2009 on trying to get their valve production under control. They never really did and it is not un-common for York valves to not be able to "spin" in the bore or have adverse wear. According to Paul, you have to know how to compensate for what happens with the boreing tools as it passes through the ports where there is no material on one side and yet is cutting material on the other side.Adams E3 0.60 Sterling bell - Prototype top sprung valves
Concord Band
Winchendon Winds
Townsend Military Band
Comment
-
-
Originally posted by daruby View PostThey had a senior technician . . .
DDavid Bjornstad
1923 Conn New Wonder 86I, Bach 6 1/2 AL
2018 Wessex EP100 Dolce, Denis Wick 4ABL
2013 Jinbao JBEP-1111L, Denis Wick 4AM
2015 Jinbao JBBR-1240, Denis Wick clone mouthpiece of unknown designation
Cullman (AL) Community Band (Euph Section Leader)
Brass Band of Huntsville (2nd Bari)
Comment
-
-
Originally posted by daruby View Post
Replating and machining the piston after replating is not the hard part. The hard part is boring and honing the cylinder (with the large holes all around it) and ending up with a perfectly round and straight sided cylinder, and THEN getting a replated piston to fit with just the right tolerances. I had a long conversation with Paul Riggett on this topic when his techs were working with York in Markneukirchen from about 2007-2009 on trying to get their valve production under control. They never really did and it is not un-common for York valves to not be able to "spin" in the bore or have adverse wear. According to Paul, you have to know how to compensate for what happens with the boreing tools as it passes through the ports where there is no material on one side and yet is cutting material on the other side.Willson 2900 TA-1 Euphonium - Denis Wick 4AM
Yamaha YSL-643 Trombone - Bob Reeves BrassArk 5G "Gladstone"
Yamaha YSL-8440 Trombone - Denis Wick 5BS
VMI 3301S BBb Tuba - Schilke Helleberg
Past:
York Preference 3067 Euphonium - Denis Wick 4AL
Benge 165F Trombone - Benge Marcellus
Wessex BR140 Baritone - Denis Wick 6BS
F.E. Olds Special Trombone (ca. 1941)
Comment
-
Comment