Page 3 of 3 FirstFirst 123
Results 21 to 21 of 21

Thread: Euphonium Shank Sizes

  1. #21
    I hate to be a random new guy that bumps an old thread, but this info needs to exist. I only just recently learned some of this the hard way. If you have a horn needing an obscure shank size, contact Josef Klier. They've helped me out a lot, and they're getting another big order from me when they get back from vacation. The numbers are as measured from the end of the mouthpiece shank.

    Normal 5% taper sizes that I know of (relevant to Tenor and Bass instruments):

    9.8mm/10mm - German Flugelhorn shank, Alto Horn, Trumpet, etc.
    A real Trumpet mouthpiece will have a tiny wobble in a real 10mm shank receiver. Supposedly, there are French made Alto Trombones with this shank.
    Shout out to the jHorn.

    10.5mm - Large Alto Shank, Large Parforcehorn Shank, Alto/Baroque/Fanfare Trumpet Shank (?)
    This is the shank size for large bore ovalform Althorns, and older Alto Trombones. Very difficult to tell the difference from small tenor unless you compare backbores.
    You can probably find some of the smaller Bb Tenorhorn's in this shank. If you have something that seems to kinda fit a Trumpet or Trombone mouthpiece, it's probably this. Good luck with backbore.

    10.8mm/11mm - Small Tenor Shank

    11.5mm - "Baritone" Shank
    To produce this size, just use Bach 381 "extension" (adapter) on a small shank mouthpiece.
    Supposedly the typical size for European Baritones. Definitely used on the Soviet Tenorhorns. I thought this was just some poorly done 11mm shank until I bought a proper vintage mouthpiece.
    This is not the same as Besson medium shank, but it might work in a pinch.

    12mm - Russian Baritone Shank
    Russian Rotary Baritones are using this super obscure shank size.
    Close to medium shank.

    12.5mm - Bass Trombone shank, Large Tenor Trombone shank, Small Tuba shank

    12.65mm - Contrabass Trombone shank, that "other" Bass Trombone shank
    Confirmed with an example. If your large shank mouthpiece seem to drop just a hair too far into your Bass Trombone, it's probably this.

    13mm - Bach Contrabass Trombone shank, Vienna Tuba

    13.5mm - Tuba shank.


    Some other stuff:

    Proprietary tapers! I purchased an old Besson just to check these. For Conn and Besson proprietary shanks, the taper is CLOSE to 5%, but it's not the same. Close enough, but expect plenty of scuffing and other issues if you mix and match or have something made.

    10.5mm? - I think this is the Olds proprietary shank?
    I never had a mouthpiece in this size, but my 1955ish Trombonium had this proprietary receiver. A 10.5mm mouthpiece worked with some nasty wobble, and an old Conn fit, but stuck out way too far.
    Seriously, if you have a horn with this...just ream it out until it plays in tune with something normal.

    11mm - Conn Small Shank
    Old versions of the 20-I and other "small shank" horns that aren't actually small shank.
    Very deep insertion depth.

    11.5mm - Conn Medium Shank
    I think this is what the 24I and 25I are using? Probably other models. I have a Precision series mouthpiece with this shank.
    If your medium shank horn doesn't bottom out, this will fit with no obvious issues.

    ~11.7mm - Besson medium shank (Euro Shank)
    Besson Euphoniums and really old B&F stencil Eb Tubas (Couesnon, Bruno NY, Goumat, etc)
    11.5mm Baritone Shank will fit with considerable scuffing and possible wobble if the leadpipe bore is large enough.
    12mm is a closer match.

    13mm - Conn Large "Remington" Shank
    Bought a Remington 6 1/2 AL-LR for cheap just so I could measure it and confirm what it is.
    This is an enormous shank type. It's longer and visibly larger than even 12.65mm bass trombone shank.
    Apparently Brown and Sharpe taper, which I guess means 4.18% taper.
    Last edited by notaverygoodname; 06-19-2020 at 01:47 AM. Reason: new and better(er) info - bought a Besson

Page 3 of 3 FirstFirst 123

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •