Results 1 to 10 of 16

Thread: Adams Custom Series Model E3 Euphonium - A Comprehensive Review - Part One

Threaded View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Apr 2014
    Location
    Summerfield, Florida Sturgis, SD (summers)
    Posts
    1,869

    Adams Custom Series Model E3 Euphonium - A Comprehensive Review - Part One

    I ordered an Adams E3 Euphonium on December 11, 2015 and received the horn at my dealer in South Dakota on May 18, 2016. The horn was expertly packed in a very strong and sturdy box. It was shipped from the factory in The Netherlands. It arrived in flawless condition. The following is a comprehensive review of this outstanding instrument. I have to do this review in two posts as the amount of information exceeds the limit for one post.

    Specifications:

    • Adams Custom Series Model E3 Euphonium, Serial # 49710
    • Sterling silver bell
    • 0.60 gauge metal
    • Bore is .590 inches 1st, 2nd, 3rd valves, .630 inches 4th valve
    • Bell diameter is 12 inches
    • Brushed finish except shiny inside bell
    • Main tuning slide trigger
    • Honduras rosewood finger button inlays
    • Vented valves
    • Full bell engraving
    • Name engraved on main tuning slide receiver
    • Water gutter for valves 1-3
    • Adjustable gap receiver
    • Blue Marcus Bonna case
    • Weighs 10 1/2 pounds, +/- 1/4 pound
    • Comes with no mouthpiece


    My wife and I have officially named the Adams Euphonium: NellyBelle

    Here are five pictures that were taken in the evening with a flash, and they show how beautiful the euphonium is:

    Click image for larger version. 

Name:	Adams1.jpg 
Views:	277 
Size:	245.0 KB 
ID:	3995 Click image for larger version. 

Name:	Adams2.jpg 
Views:	248 
Size:	243.9 KB 
ID:	3996 Click image for larger version. 

Name:	Adams3.jpg 
Views:	217 
Size:	249.2 KB 
ID:	3997 Click image for larger version. 

Name:	Adams4.jpg 
Views:	265 
Size:	265.1 KB 
ID:	3998 Click image for larger version. 

Name:	Adams5.jpg 
Views:	220 
Size:	220.4 KB 
ID:	3999

    Overall impressions:

    This is the finest euphonium I have ever played and ever owned. The sound is exquisite. The fit and finish is incomparable. The intonation is spot on and better than any horn I have played. The ergonomics of the horn are very satisfying.

    Here are several more pictures of the Adams Euphonium:

    Click image for larger version. 

Name:	Adams6.jpg 
Views:	255 
Size:	242.0 KB 
ID:	4000 Click image for larger version. 

Name:	Adams8.jpg 
Views:	266 
Size:	251.8 KB 
ID:	4001 Click image for larger version. 

Name:	Adams9.jpg 
Views:	231 
Size:	250.2 KB 
ID:	4002 Click image for larger version. 

Name:	Adams12.jpg 
Views:	222 
Size:	255.2 KB 
ID:	4003 Click image for larger version. 

Name:	Adams13.jpg 
Views:	192 
Size:	239.7 KB 
ID:	4004 Click image for larger version. 

Name:	Adams20.jpg 
Views:	217 
Size:	270.0 KB 
ID:	4005 Click image for larger version. 

Name:	Adams24.jpg 
Views:	213 
Size:	230.4 KB 
ID:	4006

    Sound:

    I prefer a sound that is somewhat mellow and warm without being too dark or tuba sounding. This horn delivers. It produces what I will describe as a very clear and very pure sound. My wife equates it to the sound of a very nice, easy to listen to, smooth male singer. Pleasing. Amazing response when playing super soft. The horn just plays the note, even at the softest levels. No matter how high or low. At louder volumes, you can't even seem to break up notes, the horn just shines and sparkles. Overtones galore. The low range really speaks more easily and solidly, and with more presence, than any other horn I have played. The high B natural, a nasty note on many euphoniums, plays fine on the Adams. High notes above Bb have more body and fullness than I have ever experienced.

    Intonation:

    Wonderful. I played up and down the horn several times with two tuners in front of me. Dave Werden's intonation chart for the Adams is very close to my results. The Eb, E, and F above tuning Bb that are usually sharp are just about spot on. The G in the staff plays well with either 1&2 or 3. The C in the staff is a little sharp using 1&3. It was even more sharp early on, but I did some fine tuning to the tuning slides since then. But that C is right on using 4 alone. I may not use the trigger much, but still glad I have it.

    The Trigger:

    From the pictures, you can see there is a little gold piece that is adjustable by one side of the main tuning slide. My name is engraved on the outer slide receiver just above this piece. You can adjust the little piece up and down, and you fix it with a set screw. It seems to do the job in not letting the slide rub against you when playing. The round cylinder like piece on the hardware attached to the main tuning slide is the adjustment for regular tuning (as in tuning to concert Bb). You simply turn it one way or the other to let the slide out or bring it in. If you look behind the 4th valve (from your perspective holding the horn in playing position), you will see the spring for the trigger paddle mechanism. There is also another long vertical screw that can go up or down. At the bottom is a black rubber stopper hooked on and the trigger mechanism rests on this when not being deployed. In other words, you press the trigger paddle, the main tuning slide goes out, then when you release the paddle, the trigger arm comes back to rest on the black rubber bumper. It is fairly compact and neat. Good design. I think the brace that is bent in a "v" shape on the main tuning slide, and where the hardware attaches, is shaped this way so that the push on the main tuning slide happens closer to the curved part of the tuning slide (which is by the way rose brass - Adams found this provides the best sound). This probably makes pushing the slide out mechanically easier than if the hardware were attached to a straight across brace. It works well.

    The Valve Area:

    Click image for larger version. 

Name:	Adams26.jpg 
Views:	206 
Size:	170.1 KB 
ID:	4007

    Valves are working splendid after a few days and only one cleaning. The valves are finely finished and look nice. There was some early chatter about the Adams valves not looking very good, but that seems to have been resolved. I ordered vented valves, and you can see the little hole in the valve which is just that. The upper valve caps screw on delightfully well, after having to worry about cross-threading on some horns. The bottom valve caps are heavier with more volume than I have been accustomed to with other horns. The springs "look" like junior high school springs, they are dinky, the smallest looking springs (at least in diameter) that I can remember seeing in a euphonium. But, they work excellent. On my Miraphone, the stock springs were not strong enough, and I got valve bounce, and after trying other springs, ended up stretching out the stock springs. In "looking" at the springs on the Adams, I would have thought they were not strong enough, but these Adams springs seem to be just about perfect for me. I can go fast and they keep up. The valve buttons have inlaid wood on them. They are flush with the brass part so if you run your finger over the finger buttons, it is totally smooth the whole way. The tops are flat, not concave or convex. The buttons are bigger in diameter than my last horn, and I much prefer this size. They just feel right, and much less chance of getting your finger stuck in between valves when you are doing the one-finger finale to Carnival of Venice. The water gutter that Adams included is nice and much like others out there. It does, however, click (or snap) into place when you put it on, so there is great feedback that you have attached it securely. The valves are quiet, at least that is how I would characterize them. Ample padding at the right places. No clacking at all. One other thing a bit different on this horn. I use a K&M stand and have for many years. It has held a Besson Prestige, Yamaha 842S, Miraphone M5050 and a Wessex Dolce. They all just slide in nicely, but I did have to adjust for each horn's width. But, with the Adams, when I put it in the K&M stand, the 4th valve touches the side rubber bracket before the horn settles all the way in. This means that the 4th valve sits low on this horn, at least lower than any others. It is unnoticeable when playing it or even looking at it, but sure enough, it is lower. I just have to tilt the horn a wee bit to get it in the stand. No big deal at all, just interesting that the 4th valve is located lower than all other horns. And, speaking about the 4th valve, there is no lock down device for the 4th valve stem on this horn. So when you put it away, the 4th valve stem is still in the ready to play position instead of locked in the down position. I thought the case for the horn would know this, but it apparently does not. There is no cubby hole spot for the 4th valve stem to fit into. When you stuff the horn in the case, the 4th valve stem just sort of gets pushed in against the side of the case. Maybe some of you who already own an Adams can say if that has caused any problems. Not sure why Adams chose to not put a lock down device on. Or at least have a solution with the case, which they do not.

    Part Two to follow.
    Last edited by John Morgan; 05-23-2016 at 10:02 AM.
    John Morgan
    The U.S. Army Band (Pershing's Own) 1971-1976
    Adams E3 Custom Series Euphonium, 1956 B&H Imperial Euphonium,
    1973 F. E. Olds & Son Studio Model T-31 Baritone
    Adams TB1 Tenor Trombone, Yamaha YBL-822G Bass Trombone
    Year Round Except Summer:
    Kingdom of the Sun (KOS) Concert Band, Ocala, FL (Euphonium)
    KOS Brass Quintet (Trombone, Euphonium)
    Summer Only:
    Rapid City Municipal Band, Rapid City, SD (Euphonium)
    Rapid City New Horizons Band (Euphonium)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •